A Guide to Understanding AEG Tumble Dryer Error Codes and Solutions
When your AEG tumble dryer runs into a problem, error codes are often the first sign that something isn’t working as it should. These codes—usually shown as numbers, letters, or flashing indicator lights—are designed to help you quickly identify what’s going wrong. Knowing what these error messages mean can save you time, money, and the hassle of unnecessary repairs.
In this blog post, we’ll take a closer look at the most common AEG tumble dryer error codes, explain what each one means, and offer practical troubleshooting tips you can try at home. Whether it’s a simple fix or a sign that professional help is needed, understanding these codes puts you in control.
By learning how to interpret your AEG dryer’s error messages, you’ll not only extend the life of your appliance but also improve its performance. Plus, we’ll share how our appliance protection plans can help you avoid costly repairs in the future—giving you peace of mind with ongoing support and coverage.
| Error Code | Description | Causes | Solution |
|---|---|---|---|
| EHO, EH0 | It indicates a problem with the power supply. | Error code EHO (EH0) or any code beginning with EH..(i.e. EH1, EH2) indicate a possible problem with the power supply, such as too low/too high voltage, unstable power supply. | 1. Check the power supply by plugging a different product into the same socket and see whether that works.
2. Reset the appliance. 3. Contact an Authorized Service Center. |
| E70 | Dryer shows error message E70 on the display. | Error code E70 indicates a problem with the temperature sensor. | 1. Reset the appliance’s control electronics by unplugging the appliance for 2 hours and then plugging it back in.
2. If this does not solve the problem and the error persists, please book a repair. We do not recommend using the product until the problem has been completely fixed. Unplug the product and do not plug it in again until you are certain that it is OK to do so. |
| Tumble Dryer generates scraping/rubbing noise while drum rotating | The Tumble Dryer generates scraping/rubbing noise while the drum rotating. | Rear drum locks have not been released correctly during the first use of the dryer. | The rear drum locks are supposed to be removed automatically when the dryer is activated for the first time without the load in the drum. Please see the dedicated section in the user manual. |
| E50 | Tumble dryer displays error message E50. | It indicates a motor or software problem. | Reset the appliance.
If this doesn’t solve the problem, please book a repair. |
| Water leakage from under the dryer | Condensate pump blocked.
Water is leaking from the dryer onto the floor. After drying, there is very little water in the water tank. A small amount of water in the condensate container. |
Blocked pump.
Incorrect operation. Dirt from clothes in the filter, clogged filter. |
A blocked condensate pump is an issue that can occur in a dryer, leading to water leaks on the floor. This is also indicated by a small amount of water collected in the condensate water container after the drying cycle.
This is a fault that requires the intervention of the support service, therefore we recommend you book a repair. |
| CE / CF | Tumble dryer displays error message CE / CF | There is a problem with the electronics. | We recommend you book a repair. |
| C8 | Tumble dryer displays error message C8. | There is a problem with the temperature sensor. | We recommend you book a repair. |
| C6 | Tumble dryer displays error message C6. | There is a problem with the moisture sensor. | We recommend you book a repair. |
| Moisture, condensation, water in tumble dryer | Moisture, condensation, water in tumble dryer. | This could be due to a number of factors. | 1. Check for any error messages on the display.
2. Make sure that the temperature of the room is between 5°C and 35°C. 3. Check if the selected cycle includes the steam phase. 4. Clean the fluff filter after each cycle. 5. Make sure the appliance is not overloaded. 6. Clean the condenser (applicable to Heat Pump Dryers and Condenser Dryers). 7. Check if the venting hose is fitted correctly (applicable to Vented Dryers). 8. Make sure the vent is open and clean (applicable to Vented Dryers). If this doesn’t solve the problem, please book a repair. |
| Tumble dryer’s Condenser LED is on | Tumble dryer’s Condenser LED is on. | Condenser needs cleaning. | Clean the condenser, filters and air ducts.
If this doesn’t solve the problem, please book a repair. |
| E80 | Tumble dryer displays error message E80. | It indicates a problem with the cycle selector or the software. |
1. Make sure the cycle selector is not set between two programme options. 2. Reset the appliance. If this doesn’t solve the problem, please book a repair. |
| E40 | Tumble dryer displays error message E40/ | The laundry could be trapped between the appliance door and rubber seal. | 1. Make sure then that the tumble dryer is not built into, for instance, an enclosed cabinet without any ventilation.
2. Install the appliance in a room with enough space and good ventilation. 3. Do not install or use the appliance where the temperature can be less than 5°C or higher than 35°C. 4. Clean the filters and door seal. 5. Check the door seal for possible damage. |
| Excessive moisture in room, on walls and windows where the tumble dryer is located | Excessive moisture in room, on walls and windows where the tumble dryer is located. | If the tumble dryer is installed in a room which is too small, condensation may occur. | Reset the appliance.
If this doesn’t solve the problem, please book a repair. |
| E54 | Tumble dryer displays error code E54. | It indicates a motor or software problem. |
Reduce the load of laundry. Check that there is no excessively heavy object in the drum, e.g. a duvet. Check another socket and make sure that there are no other appliances running at the same time. If this doesn’t solve the problem, please book a repair. |
| E9E | Tumble dryer displays error code E9E. |
Electrical noise. Humidity/water on UI board. |
Check main power supply, switch off other running appliances if necessary. The appliance is probably placed in a small closed storage room and is overheating or the air is heavy with moisture due to the lack of ventilation. Make sure that the appliance is installed in an environment with sufficient air exchange. Clean the fluff filter and the heat exchanger area. Clean the filter after each drying cycle. |
| ECA | Tumble dryer displays error code ECA. | Possible empty steam tank. | Fill water container for steam system. |
| CD | Tumble dryer displays error message CD. | There is a problem with the door’s latch. | If the door is closed properly and the tumble dryer still displays the error message, please book a repair. |
| Tumble dryer displays error message E60 and does not heat up |
Tumble dryer does not heat up. Tumble dryer does not dry properly, the laundry is wet. Tumble dryer displays the error message E60. |
It indicates a heating source problem. | 1. Make sure then that the tumble dryer is not built into, for instance, an enclosed cabinet without any ventilation.
2. Install the appliance in a room with enough space and good ventilation. 3. Clean the filters, condenser and door seal. If this doesn’t solve the problem, please book a repair. |
| E20, C2 or emits 2 beeps / 2 flashes |
Tumble dryer displays error message E20, C2 or emits 2 beeps / 2 flashes. |
It indicates a drainage, pump or software problem. | 1. Check if the external drain hose is connected correctly to a drain (if applicable).
2. Check if the drain hose is not twisted or clogged and if it has any loops (if applicable). 3. Reset the appliance. If this doesn’t solve the problem, please book a repair. |
| Err | Tumble dryer displays error message “Err”. | It appears when there is an attempt at changing a cycle or settings after the cycle has started or chosen option cannot be used with the selected cycle. | 1. Switch the dryer off and on, then select the desired cycle and options.
2. Make sure that the door is fully closed before starting the programme. |
How to Interpret AEG Tumble Dryer Error Codes and Keep Your Appliance Running Smoothly
When your AEG tumble dryer displays an error code, it’s important to identify the issue quickly to avoid further problems and ensure your appliance keeps running smoothly. Each error code points to a specific fault—from airflow blockages and overheating to sensor or drainage issues—and understanding what they mean can save you time, stress, and potentially costly repairs.
This guide is designed to help you decode AEG tumble dryer error messages, so you can troubleshoot effectively—whether it’s a simple maintenance task or a sign that professional help is needed. From clogged filters to faulty sensors, being informed puts you in control.
Keep this page handy for quick reference any time an error code appears. And for added peace of mind, be sure to check out our appliance repair services and protection plans. They’re a smart way to safeguard your tumble dryer—and all your home appliances—for the long haul.
When to Seek Professional Help for Persistent AEG Tumble Dryer Error Codes
If your AEG tumble dryer continues to display error codes, it might be time to speak with one of our experienced technicians or get in touch with AEG support for expert assistance. Staying on top of regular maintenance, addressing issues promptly, and seeking professional guidance when needed can help prevent many common tumble dryer problems from turning into bigger, more costly repairs.
If you’re having trouble with your tumble dryer, don’t hesitate to explore our specialised tumble dryer repair services or visit Home Appliance Guard for comprehensive appliance protection plans. Staying proactive in addressing error codes helps ensure your AEG tumble dryer continues to operate efficiently for years to come, while also protecting your investment with dependable repair solutions.
This is our Comprehensive Guide to AEG Tumble Dryer Error Codes
We hope this guide has been useful and got your tumble dryer working again worry free.
If you need further assistance with your tumble dryer error codes, check out our FAQ for repairs below or explore our tumble dryer repair services to restore your peace of mind—let us handle it!
AEG tumble dryers are built to make laundry care simple and efficient—but when something goes wrong, error codes are there to help you identify the issue. Whether it’s a common fault like a blocked filter or a more technical problem such as a heating error, understanding these codes can save you both time and money.
This guide offers a clear breakdown of the most frequent AEG tumble dryer error codes, what causes them, and how you can resolve them. With the right information, you can keep your dryer running smoothly and avoid unnecessary repair costs.
For additional appliance protection, visit Zest Protect for comprehensive coverage and expert support.
For more FAQs
Our appliance repair service costs £85 for the initial visit, which covers diagnosis. If replacement parts are needed, you’ll only pay for the parts, and there’s no additional charge for follow-up visits.
Repairs typically take between 30 minutes to 2 hours, depending on the appliance and the issue. If parts need to be ordered, we’ll schedule a follow-up visit for the repair.
We repair a wide range of kitchen and household appliances, including washing machines, dishwashers, ovens, fridges, freezers, microwaves, and small appliances like kettles, toasters, and coffee machines.
You pay £85 up front, and an engineer will be out to fix your appliance as soon as possible. When he gets there, if he fixes it straight away job done! If however he needs to go and buy a new part for your machine, you’ll subsequently be charged the price of that part, and only the price of the part. No charge for the revisit to repair, and you have a 6 month guarantee on the repair too.
You can request a repair by giving us a call on 0800 888 6666 or by submitting our Book a Repair Form.
